T-shirt Press 40 x 50 cm

 

 


T-shirt press 40 x 50 cm with upper lever closing. It has a robust mechanical construction with vertically adjustable heater.

You can print following items ( from our offer ):
T-shirts - Kidīs / Womenīs / Menīs / Running / Bike
 Cushions - Fine structure / Satin / Soft / Linen
 Pads - Bar / Table / Floor / Mouse
 Bags - Shopping / Toiletry
 Backpacks - School / Shoulder / Jeans
 Aprons - Fine structure / Linen
 Caps
 Bibs
 Puzzle A5 - A3
 Coaster with or without cork
 MDF boards
Flat ceramics / sublimation stones
( printing ceramics and all products that may not be perfectly flat and are also fragile, we recommend printing in 3D Press )

The digital electronic unit measures time (adjustable 0 - 999sec) and controls the temperature of the heating element (adjustable 0 - 225 C). Settings are made simply using the cursor keys.
( printing ceramics and all products that may not be perfectly flat and are also fragile, we recommend printing in 3D Press )
 

                

     e-shop / 40x50
          
   
 
   
 
 

Liberek spol. s r.o.  -  Liberek spol. s r.o.  -  Liberek spol. s r.o.  -  Liberek spol. s r.o  -  Liberek spol. s r.o.  -  Liberek spol. s r.o.  -  Liberek spol. s r.o  --  Liberek spol. s r.o.  -  Liberek spol. s r.o.  -  Liberek                                     
                               Specific features



 		 UNPACKING THE T-SHIRT PRESS

The press is packed in 2 cardboard boxes and is additionally fixed with screws on the lower wooden transport plate.
It is best to open the lids of both boxes, remove the top wooden board and carefully turn the entire press on its side. Subsequently, pull the entire press to the side, including the foam fillings
After taking it out of the box, unscrew the bottom wooden plate and and screw instead the rubber feet, which are separately in the box.
Place the press on its feet, remove the foam fillings, cut the fixing tapes that hold the press closed and carefully unpack the 220V cable


 The power of the press is 1800W, so connect the press separately (not via multiple socket) to a 220V socket.                           



PRESSURE ADJUSTMENT












 		  ! If you are not using the press, always not only switch it off, but also disconnect it from the mains (e.g. by pulling it out of the socket !

PRESSURE ADJUSTMENT
With the press turned off, adjust the pressure according to the thickness of the printed object. The press enables the printing of objects with a maximum thickness of 6 mm
Adjust the press by turning the rose (nut) as shown on th picture. Make sure that after setting the press has the pressure you want.
The press has an AUTO-OPEN function, i.e. it does not hold in the closed position when the press is switched off. If the press is switched on after closing, the electromagnet is activated, which attracts the metal pad fixed to the handle and thus holds the press in the closed position  

                                          

TEMPERATURE TIME /
SETTING

 

 















 

 



 
   
 

TEMPERATURE TIME / SETTING
  
Plug the press into the socket. The power consumption of the press is approx. 1800W, i.e. use a socket in which no other appliance is already connected.
Turn the press on with the rocker switch and set the temperature / time if needed. The default on the press is 180 C / 60 sec
 Please check the e-shop before printing, where there are recommended temperatures / times for each printable item

Control unit settings :
* press the OK button 1x and select the Celsius / Farnheit scale with the up / down cursor button
* press the OK button 2x and select the default temperature (180C) with the up / down cursor button

It is not recommended to use a temperature higher than 200C
* press the OK button 3 x and select the default time ( 60 sec ) with the up / down cursor button


                     
                                          

PRINTING






 











 

 



 
   
 
PRINTING

After setting the temperature and time, the press starts to heat up. If the temperature reaches the set value, the user is notified acoustically that he can start printing. Place the object on the base plate with the image fixed to the object to be printed and place a Teflon cover over the top and close the press.

Just before the set time expires, an acoustic signal sounds, even before the press opens automatically. Please note, automatic release means that the electromagnet holding the lever is turned off = the lever jumps up and only then the gas struts engage so that the press opens in a cultured manner in the second half of its stroke.
You can stop printing at any time by pressing the red emergency button, which releases the electromagnet and the press opens      
                                         

                              
 
                                Technical specifications
Functions  Digital adjustment of temperature and time, adjustable pressure, AUTO-OPEN feature
Operat. conditions Temperature 5 do + 400 C
Power requirements 110 / 220V, 50Hz, max 1.800 W 
Dimensions (WxHxD) 430 x 760 x 510 mm 
Weight 40 kg
Color Black / red
Accessories Mains cord     
Certification CE certificate 
    T-shirt Press
    40 x 50		       eshop lis na trika 40x50 

 
Stock spare parts       eshop spare parts